You'll have to do this pretty much by touch alone. Different engines require 2006 Kia Sorento serpentine belt replacement belts of different widths, thicknesses and lengths or circumference. Again, use the socket wrench to turn the tension pulley far enough so the 06 Kia Sedona serpentine belt replacement can be wrapped around the pulley. . It'll go back together 100x faster than it came apart. It has the Serpentine Belt Diagrams you will need. The hardest part I found was removing the bolts from the caliper and was able to get them off with some liquid wrench and a socket wrench.
So the chain doesn't need to replace what you may run into down the road is the tensioners having a problem as their is basically 3 chains in that engine. The Tensioner Pulley should move up and slightly to the left, loosening the belt enough to remove. Most likely you need to look for a grooved pulley that looks like it may not be related to any parts of the engine, i. A couple of cracks every 3 inches is normal, but if you see cracks every 1-2 inches I would recommend that you replace it. Remove each of the fan housings; it is a tight fit to get them out. The Driveworks v-belt delivers long-lasting dependable belt life. Attach the socket and set the direction to tighten the same direction the spring action allows the pulley to move.
Also note that the brake pads will be flush up against the rotor. Installation is the reverse of the above. Tensioners are brand-new, pulleys align perfectly and there is nothing leaking on the belts or any dirt in the pulley grooves. Just reverse the procedure to replace. This pulley is attached to a very strong spring and holds the belt tight against the pulleys through its serpentine route around the engine.
Simpler, less costly method than the original below: 1. I just finished doing this job for a friend last weekend. Different engines require 2006 Kia Sedona serpentine belt replacement belts of different widths, thicknesses and lengths or circumference. When I did this the other week, I was afraid I would break the console by pulling too hard, but it un-clipped an came right down. This requires going under the vehicle. The new belt will need more clearance to get on the pulley.
This must be done correctly. Disconnect the sensor and horns. An 2006 Kia Sorento serpentine belt replacement too small will bind the pulleys while an 06 Kia Sorento serpentine belt replacement too large will just fall off. Re-tighten the bolt in the center of the pulley. With the correct size wrench you would turn the pulley either cw or ccw in turning the bolt in the middle of the pulley it will not loosen the bolt but actually relieve spring tension to release tension on the belt and then remove the belt. Use a 14mm socket to loosen the bolt which goes thru the tensioner pulley. You do have a cam timing belt that runs around both of your camshafts and crankshaft pulley.
It is alot cheaper to replace the belt before it breaks. Then, loosen the tensioner bracket hex screw and adjust the tensioner hex screw that runs through that. You'll know if they aren't because the caliper will not go back over the new pads until they are. Turn the wrench handle, the pulley moves and the tension on the belt slackens. As the crankshaft pulley turns, it moves the serpentine belt, which then spins the other pulleys.
An 2006 Kia Sedona serpentine belt replacement too small will bind the pulleys while an 06 Kia Sedona serpentine belt replacement too large will just fall off. Loosen the bolt in the center of the pulley, then under the pulley, turn the other 14mm bolt clockwise to tighten. Use a socket wrench with a matching socket the same size as the hex head bolt in the center of the tension pulley. Remove the alternator, disconnect the electrical and remove the mounting bracket that mounts to the engine. You only need to replace any belt when it is worn past its useful life. Disconnect upper coolant hose bracket from the engine and it push up on top of the engine. Find the tension pulley located at the bottom of the motor.
Now it is time to put the caliper back on. Installation is the reverse of these instructions. I believe you can handle it from there? Jan 30, 2016 The 3. Let me know if this helped, or if you have additional information or questions. Yours may be larger or smaller. I actually think it takes less time, but better safe than sorry. Turn the wrench handle, the pulley moves and the tension on the belt slackens.